VECHRO ISOLOR HYBRID AQUA PLUS ELASTOMERIC INSULATION PAINT

Water based high solids hybrid elastomeric waterproofing coating with high tech acrylic and polyurethane resins.
Fast curing and water tight againstponding water.

Ιt develops a water vapour diffusive coating, which keeps its elasticity from -20°C up to +80°C and is non-sticky, walkable and resistant to pedestrian traffic.

Excellent crack bridging ability up to 1,5mm.

Its innovative synthesis permits high build coating even in one coat (1,5kg/m2), very good dirty pick up resistance and superior thermoreflective
properties.

It is certified as cool-thermoreflective coating.

Reliable and cost-effective water proofing solution.

Easy to apply.

ISOLOR HYBRID AQUA plus carries the CE mark as it is certified by EN-1504-2 as a concrete protection product against penetration, moisture control and increased resistance to limiting the moisture content.

It is also certified as cold - reflective material (CRES, DEMOKRITOS) and offers excellent heat - refraction (reducing the cooling cost in the summer months).

It is a solution of excellent cost-effectiveness in sealing maintenance with or without the use of glass or polyester reinforcement strips.

Easy application and maintenance (by qualified or unskilled personnel), user friendly and environment friendly

Specific Gravity 1,50-1,54 kg/lt

Covering Power and Consumption 1, 25-2 m2 /kg & 0,5-0,8 m2 /kg (roller application) per coat and 0,7-1 m2 /kg & 1- 1,5kg/m2 (thick brush application) depending on
surface roughness

Dilution Up to 5% on volume with water. For application on old bituminous roofing, the first coat should be diluted up to 10%.

Drying 1-3 hours touch free. Recoat able 8-12 hours.

Recoatability 6-12 hours after first layer’s application These times prolong under
cold and wet weather conditions. Walkable after 3-4 hours.

Water & Alkali resistance Very good water and alkali resistance.

Elasticity & Elongation at break 350% elongation, film thickness up to 1mm and temperature 23°C
&. 100% elongation, film thickness up to 1mm and temperature 10°C & Keeps elasticity on temperatures between –20°C and 80°C.

VOC Class “Exterior wall coatings of mineral substrate”. Type WB. VOC limit=40 gr/lt. Max VOC of product ready for use = 39 gr/lt. VOC: organic
volatile compounds wit boiling point < 250°C.

Application tools Brush, Roller, Airless Spray

Shades White, Red-brown.

Reflection in visible spectrum R= 89,5% ±2% (400-750 nm, ASTM E903-96)

Reflection in Infra-Rede (IR) area R=89,5% ± 2% (780‐2500 nm, ASTM E903‐96)

Emission Coefficient 0,88 (ε, ASTM E408‐71)

Adhesion on concrete >4MPa (EN 24624)

Adhesion on concrete on which Isolor Hybrid Primer has been applied >6MPa (EN 24624)

Tensile Strengh ( 23°C /-20°C) N/mm² = 1.4 / 7.5

SURFACE PREPARATION
New surfaces: apply Isolor Hybrid Primer, which is ready for use
without delusion. Old surfaces: Clean the surface of dust, oil,
cropped paints, rust and dampness. If needed use repair products
like Smaltofill elastic putty and/or polyester reinforcement material and/or PU shielding products. Then apply Isolor Hybrid Primer.

APPLICATION
Stir well. Apply uniformly ISOLOR Hybrid Aqua Plus. Higher consumption of the product per m2 affects the lifetime expectancy of
the coating. The use of polyester reinforcement
material needs for the application three coats of ISOLOR Hybrid
Aqua Plus+. Put the reinforcement material on the wet first coat.
After the drying, apply additional two coats.

CLEANING EQUIPMENT
While working keep your equipment wet, either in the pot, or in
the paint lauder. Strain well your tools from paint back to the pot
and clean immediately with warm water and soap.

APPLICATION CONDITIONS
Temperature 8-350C and relative humidity lower than 80%. Do not apply in case of imminent rain.

STORAGE
Close well after application. Store in a cool place. Protect from freezing and sun exposure.